shareage0

Peugeot 208 Key Replacement Peugeot 208 key replacement is best left to experienced auto locksmiths with the right equipment and technical knowledge. They can design and program keys faster and cheaper than dealers. If the key fob has stopped locking or unlocking your doors it could be due to a dead coin battery. But, there are other reasons that the key may be malfunctioning. Dead Coin Battery A dead coin battery will hinder your Peugeot 208 from locking or unlocking and won't start the engine. If this is the case, you'll need to use the backup starting method which is explained in your vehicle's owner manual. The spark plugs may also be worn out. The spark plugs ignite fuel to start the engine. They are only able to last for a short time. If they are not used enough, they will eventually fail. Luckily, there is an easy solution for this issue. The best way to solve this issue is to test the voltage of your car battery with a multimeter. If it's below 11.5 Volts it is time to replace it. It is also necessary to clean the contacts of the battery in the event that it is damaged by corrosion. This can be done by lifting the rubber covers that cover both battery terminals and using wire brushes to clean any corroded components of the battery. You should then reconnect your cables to connect the positive and negative poles. Water Damage If your 208 won't start and the battery is not flat then you should check that the spark plugs are in good working order. It could be that they are simply too dirty and do not spark. The spark plugs can be cleaned in the workshop. Peugeot cars have a transponder style key that works with the car's ignition system. This ensures that only a valid key is able to turn the engine. If the chip in the Peugeot key is damaged then it will not transmit the proper signal to the vehicle. Water damage is a frequent reason for this issue. This is a common problem in more cold climates where the car is exposed to snow or rain. In this case, you need to contact a reputable locksmith who has the necessary tools and equipment to change the key's programming. They also have the most up-to-date technology and the machinery needed to make the Peugeot 208 smart key. The process shouldn't take longer than 15 minutes. Contacts of the battery may be damaged. Peugeot changed from the old carbon encased transponder chips to a brand new type of chip that uses electronic components on circuit boards. The new system is effective when it's brand new, however, over time, the circuit boards start to deteriorate and stop working properly. This could stop the immobiliser chip from working, so your car won't start. Contact a Peugeot specialist or a locksmith if this is the situation. peugeot key is when the battery of the key fob starts to fail. This causes the blade of the key to stop feeding into your lock. A car locksmith can replace the battery and cut a new blade for you, it's normally a quick fix. Faulty Receiver Module If your Peugeot key fob has stopped working after dropping it on the floor, being exposed to a sudden rain or accidently washing it may be due to a faulty receiver module. The receiver is responsible for sending radio frequency signals to an on-board computer that controls the central locking system in your Peugeot vehicle. The key fob itself is fitted with rubber seals to prevent water from getting to the electronic chip inside. The chip can be damaged by water if it is exposed to water for a long time. The high salt content in the pool or ocean waters can cause damage to the key fob when it is submerged. The module must be replaced if your Peugeot spare key isn't working anymore. This is only done by a Peugeot specialist or an expert auto locksmith. Peugeot keys like other cars are protected by an immobilizer system. This requires the proper programming to allow the car to start. This is why you should go with a knowledgeable Peugeot locksmith to take on the job of creating and programming a replacement. Faulty on-Board computer The on-board computer of your Peugeot is responsible for a variety of features in your car, including airbags and power windows. The on-board computer will display a code when something goes wrong. This code is stored in the system and stays there until the problem is resolved. Usually, this will mean replacing the on-board computer. The most common cause of the warning light for airbags to illuminate is corrosion or loose connections in the sensor. This can be caused by wear and tear, ageing, or exposure to salt and moisture. It is imperative to have this issue addressed as quickly as possible, as an airbag that is malfunctioning can be dangerous in the event of an accident. If your Peugeot is showing a card not detected error then the key battery in the key fob may be dead or weak. This will stop the key fob from sending a signal to disarm the vehicle's immobilizer. You can test this by pressing the unlock button on the key fob, then attempting to start your vehicle. If this fails, then the key battery will need replacing.